
Reference: T1601rc
Brand: Trackmate Racing
Transponder
Trackmate Iridium transponder for RC car.New version, half the size.
Reference: T1601rc
Brand: Trackmate Racing
Trackmate Iridium transponder for RC car.New version, half the size.
Reference: Iridium-m
Brand: Trackmate Racing
Compatible with the Trackmate RC lap counter. Installed in a bridge that goes across the track. Each one can cover 14.5"(36cm). Connecting cable is included.
Reference: 810
Brand: Trackmate Racing
Complete package hardware and software. Infrared RC Lap Counter / Timer for radio Controlled cars. This is everything you need to start racing on a track that is 10 feet wide.
Reference: trans-10
Brand: Trackmate Racing
SAVE 34% Transponders pack of 10 for R/C cars
Reference: TRANS-25
Brand: Trackmate Racing
SAVE 37% Transponders pack of 25 for R/C cars
Reference: trc-5
Brand: Trackmate Racing
SAVE 34% Transponders pack of 5 For R/C cars
This is a driver station also called a controller hook up panel. Accepts banana plugs or aligator clips. 10 amp Direction switch. Compatible with electronic controllers. LED indicators.
Also get the Mini Relay panel, highly recommended for a super easy installation.
Measures: 4.3" x 2.25" 1.2" deep (108mm x 57mm 28mm deep)
Also available with out the box part# TM103
Ffeatures
See video below on how to solder wires to track rails
Reference: SC104
Brand: Trackmate Racing
Makes connecting to relay very easy, 2 terminal screws for each lane. Two terminal screws for relay coil.
2 conductor 18 gauge wire 25' red and black, Ideal for wiring HO or 1:32 scale tracks.
Reference: 12v500ma
12 volt adapter. 500ma. For Slot car interface. Replaces older 9 volt adapters that were used in the past.Also used on LED Bridge/Gantries.
Reference: 113
3 Alligator clips in White, Black and Red colors. Solder to controller wires
This relay board will handle any track power. Ideal for commercial 1:24 scale type tracks. 30amp relays per lane. Designed to connect to a blue Trackmate interface. This is not for sell time. All relays turn off/on at the same time. A 12v 1.6 amp power adapter is required to be used with the Trackmate Blue interface, when using this relay board
2 conductor 18 gauge wire 25' red and black, Ideal for wiring HO or 1:32 scale tracks.
Reference: ac232
USB to serial. Required if your computer does not have a 9 pin serial port and only has USB ports. New computers will most likely require the USB to serial.
Reference: Reed-4
Brand: Trackmate Racing
Four Reed switches for $14, Including heat shrink, Keep spares. Normally used with HO slot car lap counters.
Reference: RLY8
The perfect relay panel for 1:24 scale commercial tracks that run on batteries or 50 amp to 95 amp power supplies. Relay panel comes with 8 relays and master relay. Can be easily connected to Trackmate Commerical Interface.
Reference: GANTRY
Brand: Trackmate Racing
Gantry (Bridge) Uses infrared LEDs for light source. Recommended when using infrared sensors for lap counter . Includes DC adapter. Wires can go through table and be completely hidden. (Track not included). Click view and select type
Reference: CVGA-XX
Brand: Trackmate Racing
VGA extension cable - click view button and select length 15 pin Male / Female cable
Reference: flood8xx
Brand: Trackmate Racing
https://youtu.be/7NRAQ25uLaI?si=04Kl-lH8VNNlePq4&t=146Infrared Flood Bar, No alignment with sensors required. Select length required 12 Volt adapter included.
Reference: 12v1600n
12 volt adapter rated to 1.6 amps. Used on Sell time units with 4 to 8 relays. Required if you want to power more than 3 relays on a Trackmate interface.
Reference: PD6
Brand: Trackmate Racing
High quality power distribution box, no soldering or crimping required. Simply strip 3/16 inch from wire end and insert and screw down. One input and 6 power tap outputs. One required per lane. Board can be removed and then box can be securely screwed down for easy mounting.
Reference: TM103
Brand: Trackmate Racing
This is a driver station also called a controller hook up panel. Accepts banana plugs or aligator clips. 10 amp Direction switch. Compatible with electronic controllers. LED indicators.
Reference: ban3
3 banana plugs in white, black and red colors. Solder to controller wires
Reference: RLY4
Relay panel with 4 relays, one per lane giving the ability to control each lane individualy. Call for details
2 conductor 18 gauge wire 100 feet red and black, Ideal for wiring HO or 1:32 scale tracks.
This is a driver station also called a controller hook up panel. Accepts banana plugs or aligator clips. 10 amp Direction switch. Compatible with electronic controllers. LED indicators.