Reference: T1601rc
Brand: Trackmate Racing
Trackmate Iridium transponder for RC car.New version, half the size.
Reference: Iridium-m
Brand: Trackmate Racing
Compatible with the Trackmate RC lap counter. Installed in a bridge that goes across the track. Each one can cover 14.5"(36cm). Connecting cable is included.
Reference: 810
Brand: Trackmate Racing
Complete package hardware and software. Infrared RC Lap Counter / Timer for radio Controlled cars. This is everything you need to start racing on a track that is 10 feet wide.
Reference: trans-10
Brand: Trackmate Racing
SAVE 34% Transponders pack of 10 for R/C cars
Reference: TRANS-25
Brand: Trackmate Racing
SAVE 37% Transponders pack of 25 for R/C cars
Reference: trc-5
Brand: Trackmate Racing
SAVE 34% Transponders pack of 5 For R/C cars
Recommended only for tracks that use four stock power packs. This relay has a set of contacts for each power pack.
Reference: flood850n
Brand: Trackmate Racing
Infrared Flood Bar assembled, A light source for sensors in the track. No alignment required. Select the length you need.
Reference: 12v500ma
12 volt adapter. 500ma. For Slot car interface. Replaces older 9 volt adapters that were used in the past.Also used on LED Bridge/Gantries.
Reference: CBL-s
Brand: Trackmate Racing
Sensor Cable with 8 pin connector (RJ45). For new black Trackmate interface SCL3-USB. Available in Infrared, Dead Strip and Reed type. Click view then select cable type.
Reference: 12v1600n
12 volt adapter rated to 1.6 amps. Used on Sell time units with 4 to 8 relays. Required if you want to power more than 3 relays on a Trackmate interface.
Reference: SCLW
Wireless track call button, will require to solder 2 wires to the Tackmate interface, instructions included. Works up to 60 feet!
Reference: SCL-R
Brand: Trackmate Racing
Discontinued.Replacement module for Trackmate Lap Counter. Click details to see power adapter options.
Reference: ac232
USB to serial. Required if your computer does not have a 9 pin serial port and only has USB ports. New computers will most likely require the USB to serial.
Reference: GANTRY
Brand: Trackmate Racing
Gantry (Bridge) Uses infrared LEDs for light source. Recommended when using infrared sensors for lap counter . Includes DC adapter. Wires can go through table and be completely hidden. (Track not included). Click view and select type
Reference: flood8xx
Brand: Trackmate Racing
https://youtu.be/7NRAQ25uLaI?si=04Kl-lH8VNNlePq4&t=146Infrared Flood Bar, No alignment with sensors required. Select length required 12 Volt adapter included.
Four Infrared LEDs. These LEDs are extremely good. Good range and uniform cover. Perfect alignment is not required. Also check out our complete LED kit with adapter.
Reference: Jumbo
Track call button. Start and pause race. Normally uses with the relay option. Connect one or many.
Adapter to use existing 25 pin sensor cable with the newer Trackmate black Interface SCL3-USB with RJ45 8 pin connector. Will only work with 1 to 4 lane cables.
Save dollars on your Slot car lap counter. This is a Do It Yourself version of the prewired LED kit. All the parts included to make an overhead light source for an infrared lap counter. Includes instructions, power adapter, LEDs, heat shrink, Connector and wire.
Reference: IRSENSORS
Brand: Trackmate Racing
5 infrared sensors 3mm, includes heat shrink. Keep spares
Reference: Reed-4
Brand: Trackmate Racing
Four Reed switches for $14, Including heat shrink, Keep spares. Normally used with HO slot car lap counters.
Recommended only for tracks that use four stock power packs. This relay has a set of contacts for each power pack.
