Reference: T1601rc
Brand: Trackmate Racing
Trackmate Iridium transponder for RC car.New version, half the size.
Reference: Iridium-m
Brand: Trackmate Racing
Compatible with the Trackmate RC lap counter. Installed in a bridge that goes across the track. Each one can cover 14.5"(36cm). Connecting cable is included.
Reference: 810
Brand: Trackmate Racing
Complete package hardware and software. Infrared RC Lap Counter / Timer for radio Controlled cars. This is everything you need to start racing on a track that is 10 feet wide.
Reference: trans-10
Brand: Trackmate Racing
SAVE 34% Transponders pack of 10 for R/C cars
Reference: TRANS-25
Brand: Trackmate Racing
SAVE 37% Transponders pack of 25 for R/C cars
Reference: trc-5
Brand: Trackmate Racing
SAVE 34% Transponders pack of 5 For R/C cars
Infrared Flood Bar assembled, A light source for sensors in the track. No alignment required. Select the length you need.
Select the length you need. Build your own bridge and mount the flood bar strip underneath it. No soldering required. 6 foot wire included. the height of the bridge should be 3 to 4 inches. requires 12 volts. Can be powered by the new blue box lap counting interface. The length you need is the distance from the first slot to the last slot.
Reference: CBL-s
Brand: Trackmate Racing
Sensor Cable. Older style with 25 pin connector. Available in Infrared, Dead Strip and Reed type. Click view then select cable type.
Reference: CBL-s
Brand: Trackmate Racing
Sensor Cable with 8 pin connector (RJ45). For new black Trackmate interface SCL3-USB. Available in Infrared, Dead Strip and Reed type. Click view then select cable type.
Adapter to use existing 25 pin sensor cable with the newer Trackmate black Interface SCL3-USB with RJ45 8 pin connector. Will only work with 1 to 4 lane cables.
Reference: 12v500ma
12 volt adapter. 500ma. For Slot car interface. Replaces older 9 volt adapters that were used in the past.Also used on LED Bridge/Gantries.
Reference: SCLC-unit
Replacement unit only. Slot car lap counter with time sell, to sell time per lane.Does NOT include Relay board, sensor cable, track call buttons
Reference: SCL3
Brand: Trackmate Racing
Substitute module for the Trackmate SCL81 USB Lap/Timer Counter, originally designed in 2014. Features integrated USB functionality, eliminating the need for a USB to serial adapter. Capable of supporting 8 lanes and compatible with 8-pin sensor cables.
Reference: IRSENSORS
Brand: Trackmate Racing
5 infrared sensors 3mm, includes heat shrink. Keep spares
Reference: 12v1600n
12 volt adapter rated to 1.6 amps. Used on Sell time units with 4 to 8 relays. Required if you want to power more than 3 relays on a Trackmate interface.
Reference: Jumbo
Track call button. Start and pause race. Normally uses with the relay option. Connect one or many.
Reference: SC106
Brand: Trackmate Racing
For 6 lanes. Makes connecting to relay very easy, 2 terminal screws for each lane. Two terminal screws for relay coil.
Reference: ac232
USB to serial. Required if your computer does not have a 9 pin serial port and only has USB ports. New computers will most likely require the USB to serial.
Reference: usbab-15
USB cable Type AB for Trackmate interface SCL3usb. 15ft long. This is longest USB cable you can use.
Reference: SCLW
Wireless track call button, will require to solder 2 wires to the Tackmate interface, instructions included. Works up to 60 feet!
Reference: GANTRY
Brand: Trackmate Racing
Gantry (Bridge) Uses infrared LEDs for light source. Recommended when using infrared sensors for lap counter . Includes DC adapter. Wires can go through table and be completely hidden. (Track not included). Click view and select type
Recommended only for tracks that use four stock power packs. This relay has a set of contacts for each power pack.
Infrared Flood Bar assembled, A light source for sensors in the track. No alignment required. Select the length you need.
