Reference: T1601rc
Brand: Trackmate Racing
Trackmate Iridium transponder for RC car.New version, half the size.
Reference: Iridium-m
Brand: Trackmate Racing
Compatible with the Trackmate RC lap counter. Installed in a bridge that goes across the track. Each one can cover 14.5"(36cm). Connecting cable is included.
Reference: trans-10
Brand: Trackmate Racing
SAVE 34% Transponders pack of 10 for R/C cars
Reference: 810
Brand: Trackmate Racing
Complete package hardware and software. Infrared RC Lap Counter / Timer for radio Controlled cars. This is everything you need to start racing on a track that is 10 feet wide.
Reference: TRANS-25
Brand: Trackmate Racing
SAVE 37% Transponders pack of 25 for R/C cars
Reference: trc-5
Brand: Trackmate Racing
SAVE 34% Transponders pack of 5 For R/C cars
High-quality power distribution box designed for quick and easy wiring. No soldering or crimping required — simply strip 3/16 inch of insulation from the wire, insert it into the terminal, and tighten the screw. Features one power input and six power tap outputs. One unit is required per lane. The internal board can be removed, allowing the enclosure to be securely screwed down for easy mounting.
Can be used for general purpose low voltage distribution, one box will handle + and - IN and 6 Outputs. Can be screwed down.
Applications:
Reference: Reed-4
Brand: Trackmate Racing
Four Reed switches for $14, Including heat shrink, Keep spares. Normally used with HO slot car lap counters.
Reference: flood8xx
Brand: Trackmate Racing
https://youtu.be/7NRAQ25uLaI?si=04Kl-lH8VNNlePq4&t=146Infrared Flood Bar, No alignment with sensors required. Select length required 12 Volt adapter included.
Reference: 12v500ma
12 volt adapter. 500ma. For Slot car interface. Replaces older 9 volt adapters that were used in the past.Also used on LED Bridge/Gantries.
12 volt 500ma replacement power pack/ adapter RC lap counter, Slot car lap counter, Drag_Pro2000/3000
Reference: TM104-BLK
Brand: Trackmate Racing
This is a driver station also called a controller hook up panel. Accepts banana plugs or aligator clips. 10 amp Direction switch. Compatible with electronic controllers. LED indicators. *** NOW IN COLOR
Reference: SCLW
Wireless track call button, will require to solder 2 wires to the Tackmate interface, instructions included. Works up to 60 feet!
Reference: TM104-BLK
Brand: Trackmate Racing
This is a driver station also called a controller hook up panel. Accepts banana plugs or aligator clips. 10 amp Direction switch. Compatible with electronic controllers. LED indicators. *** NOW IN COLOR
Reference: CBL-9EXT-30
Brand: Trackmate Racing
Serial Cable. Long serial cables allow computer to be far away from the track. Can be used with Red or Green Trackmate SCL slot car interface, DP3000, DP2000.
Reference: TM104
Brand: Trackmate Racing
This is a driver station also called a controller hook up panel. Accepts banana plugs or aligator clips. 10 amp Direction switch. Compatible with electronic controllers. LED indicators.
Reference: 12v1600n
12 volt adapter rated to 1.6 amps. Used on Sell time units with 4 to 8 relays. Required if you want to power more than 3 relays on a Trackmate interface.
2 conductor 18 gauge wire 100 feet red and black, Ideal for wiring HO or 1:32 scale tracks.
Reference: SC106
Brand: Trackmate Racing
For 6 lanes. Makes connecting to relay very easy, 2 terminal screws for each lane. Two terminal screws for relay coil.
Reference: 113
3 Alligator clips in White, Black and Red colors. Solder to controller wires
Reference: ac232
USB to serial. Required if your computer does not have a 9 pin serial port and only has USB ports. New computers will most likely require the USB to serial.
Reference: flood850n
Brand: Trackmate Racing
Infrared Flood Bar assembled, A light source for sensors in the track. No alignment required. Select the length you need.
Reference: ban3
3 banana plugs in white, black and red colors. Solder to controller wires
High-quality power distribution box designed for quick and easy wiring. No soldering or crimping required — simply strip 3/16 inch of insulation from the wire, insert it into the terminal, and tighten the screw. Features one power input and six power tap outputs. One unit is required per lane. The internal board can be removed, allowing the enclosure to be securely screwed down for easy mounting.
