Reference: T1601rc
Brand: Trackmate Racing
Trackmate Iridium transponder for RC car.New version, half the size.
Reference: Iridium-m
Brand: Trackmate Racing
Compatible with the Trackmate RC lap counter. Installed in a bridge that goes across the track. Each one can cover 14.5"(36cm). Connecting cable is included.
Reference: trans-10
Brand: Trackmate Racing
SAVE 34% Transponders pack of 10 for R/C cars
Reference: 810
Brand: Trackmate Racing
Complete package hardware and software. Infrared RC Lap Counter / Timer for radio Controlled cars. This is everything you need to start racing on a track that is 10 feet wide.
Reference: TRANS-25
Brand: Trackmate Racing
SAVE 37% Transponders pack of 25 for R/C cars
Reference: trc-5
Brand: Trackmate Racing
SAVE 34% Transponders pack of 5 For R/C cars
High-quality power distribution box designed for quick and easy wiring. No soldering or crimping required — simply strip 3/16 inch of insulation from the wire, insert it into the terminal, and tighten the screw. Features one power input and six power tap outputs. One unit is required per lane. The internal board can be removed, allowing the enclosure to be securely screwed down for easy mounting.
Can be used for general purpose low voltage distribution, one box will handle + and - IN and 6 Outputs. Can be screwed down.
Applications:
Reference: TM104
Brand: Trackmate Racing
This is a driver station also called a controller hook up panel. Accepts banana plugs or aligator clips. 10 amp Direction switch. Compatible with electronic controllers. LED indicators.
Reference: SC104
Brand: Trackmate Racing
Makes connecting to relay very easy, 2 terminal screws for each lane. Two terminal screws for relay coil.
12 volt 500ma replacement power pack/ adapter RC lap counter, Slot car lap counter, Drag_Pro2000/3000
Reference: flood8xx
Brand: Trackmate Racing
https://youtu.be/7NRAQ25uLaI?si=04Kl-lH8VNNlePq4&t=146Infrared Flood Bar, No alignment with sensors required. Select length required 12 Volt adapter included.
Reference: GANTRY
Brand: Trackmate Racing
Gantry (Bridge) Uses infrared LEDs for light source. Recommended when using infrared sensors for lap counter . Includes DC adapter. Wires can go through table and be completely hidden. (Track not included). Click view and select type
Reference: ban3
3 banana plugs in white, black and red colors. Solder to controller wires
Reference: TM104-BLK
Brand: Trackmate Racing
This is a driver station also called a controller hook up panel. Accepts banana plugs or aligator clips. 10 amp Direction switch. Compatible with electronic controllers. LED indicators. *** NOW IN COLOR
Reference: TM104-BLK
Brand: Trackmate Racing
This is a driver station also called a controller hook up panel. Accepts banana plugs or aligator clips. 10 amp Direction switch. Compatible with electronic controllers. LED indicators. *** NOW IN COLOR
Reference: RLY4
Relay panel with 4 relays, one per lane giving the ability to control each lane individualy. Call for details
Reference: 12v1600n
12 volt adapter rated to 1.6 amps. Used on Sell time units with 4 to 8 relays. Required if you want to power more than 3 relays on a Trackmate interface.
Reference: flood850n
Brand: Trackmate Racing
Infrared Flood Bar assembled, A light source for sensors in the track. No alignment required. Select the length you need.
Reference: CBL-9EXT-30
Brand: Trackmate Racing
Serial Cable. Long serial cables allow computer to be far away from the track. Can be used with Red or Green Trackmate SCL slot car interface, DP3000, DP2000.
Reference: 113
3 Alligator clips in White, Black and Red colors. Solder to controller wires
Reference: TM103
Brand: Trackmate Racing
This is a driver station also called a controller hook up panel. Accepts banana plugs or aligator clips. 10 amp Direction switch. Compatible with electronic controllers. LED indicators.
2 conductor 18 gauge wire 100 feet red and black, Ideal for wiring HO or 1:32 scale tracks.
2 conductor 18 gauge wire 25' red and black, Ideal for wiring HO or 1:32 scale tracks.
High-quality power distribution box designed for quick and easy wiring. No soldering or crimping required — simply strip 3/16 inch of insulation from the wire, insert it into the terminal, and tighten the screw. Features one power input and six power tap outputs. One unit is required per lane. The internal board can be removed, allowing the enclosure to be securely screwed down for easy mounting.
