Reference: T1601rc
Brand: Trackmate Racing
Trackmate Iridium transponder for RC car.New version, half the size.
Reference: Iridium-m
Brand: Trackmate Racing
Compatible with the Trackmate RC lap counter. Installed in a bridge that goes across the track. Each one can cover 14.5"(36cm). Connecting cable is included.
Reference: 810
Brand: Trackmate Racing
Complete package hardware and software. Infrared RC Lap Counter / Timer for radio Controlled cars. This is everything you need to start racing on a track that is 10 feet wide.
Reference: trans-10
Brand: Trackmate Racing
SAVE 34% Transponders pack of 10 for R/C cars
Reference: TRANS-25
Brand: Trackmate Racing
SAVE 37% Transponders pack of 25 for R/C cars
Reference: trc-5
Brand: Trackmate Racing
SAVE 34% Transponders pack of 5 For R/C cars
This is a driver station also called a controller hook up panel. Accepts banana plugs or aligator clips. 10 amp Direction switch. Compatible with electronic controllers. LED indicators. *** NOW IN COLOR
Also get the Mini Relay panel, highly recommended for a super easy installation.
Measures: 4.3" x 2.25" 1.2" deep (108mm x 57mm 28mm deep)
Also available with out the box part# TM103
Features
See video below on how to solder wires to track rails
Tip: Use 18 gauge wire when soldering to the rails, bigger wire will be extremely difficult.
Reference: SC104
Brand: Trackmate Racing
Makes connecting to relay very easy, 2 terminal screws for each lane. Two terminal screws for relay coil.
2 conductor 18 gauge wire 25' red and black, Ideal for wiring HO or 1:32 scale tracks.
This relay board will handle any track power. Ideal for commercial 1:24 scale type tracks. 30amp relays per lane. Designed to connect to a blue Trackmate interface. This is not for sell time. All relays turn off/on at the same time. A 12v 1.6 amp power adapter is required to be used with the Trackmate Blue interface, when using this relay board
Reference: 12v1600n
12 volt adapter rated to 1.6 amps. Used on Sell time units with 4 to 8 relays. Required if you want to power more than 3 relays on a Trackmate interface.
Reference: 113
3 Alligator clips in White, Black and Red colors. Solder to controller wires
Reference: Reed-4
Brand: Trackmate Racing
Four Reed switches for $14, Including heat shrink, Keep spares. Normally used with HO slot car lap counters.
12 volt 500ma replacement power pack/ adapter RC lap counter, Slot car lap counter, Drag_Pro2000/3000
Reference: SC104
Brand: Trackmate Racing
Makes connecting to relay very easy, 2 terminal screws for each lane. Two terminal screws for relay coil.
Reference: ban3
3 banana plugs in white, black and red colors. Solder to controller wires
Reference: CVGA-XX
Brand: Trackmate Racing
VGA extension cable - click view button and select length 15 pin Male / Female cable
Reference: TM103
Brand: Trackmate Racing
This is a driver station also called a controller hook up panel. Accepts banana plugs or aligator clips. 10 amp Direction switch. Compatible with electronic controllers. LED indicators.
Reference: TM104-BLK
Brand: Trackmate Racing
This is a driver station also called a controller hook up panel. Accepts banana plugs or aligator clips. 10 amp Direction switch. Compatible with electronic controllers. LED indicators. *** NOW IN COLOR
Reference: CBL-9EXT-30
Brand: Trackmate Racing
Serial Cable. Long serial cables allow computer to be far away from the track. Can be used with Red or Green Trackmate SCL slot car interface, DP3000, DP2000.
Reference: RLY4
Relay panel with 4 relays, one per lane giving the ability to control each lane individualy. Call for details
Reference: 12v500ma
12 volt adapter. 500ma. For Slot car interface. Replaces older 9 volt adapters that were used in the past.Also used on LED Bridge/Gantries.
Reference: TM104
Brand: Trackmate Racing
This is a driver station also called a controller hook up panel. Accepts banana plugs or aligator clips. 10 amp Direction switch. Compatible with electronic controllers. LED indicators.
Save dollars on your Slot car lap counter. This is a Do It Yourself version of the prewired LED kit. All the parts included to make an overhead light source for an infrared lap counter. Includes instructions, power adapter, LEDs, heat shrink, Connector and wire.
2 conductor 18 gauge wire 100 feet red and black, Ideal for wiring HO or 1:32 scale tracks.
This is a driver station also called a controller hook up panel. Accepts banana plugs or aligator clips. 10 amp Direction switch. Compatible with electronic controllers. LED indicators. *** NOW IN COLOR
