Reference: T1601rc
Brand: Trackmate Racing
Trackmate Iridium transponder for RC car.New version, half the size.
Reference: Iridium-m
Brand: Trackmate Racing
Compatible with the Trackmate RC lap counter. Installed in a bridge that goes across the track. Each one can cover 14.5"(36cm). Connecting cable is included.
Reference: 810
Brand: Trackmate Racing
Complete package hardware and software. Infrared RC Lap Counter / Timer for radio Controlled cars. This is everything you need to start racing on a track that is 10 feet wide.
Reference: trans-10
Brand: Trackmate Racing
SAVE 34% Transponders pack of 10 for R/C cars
Reference: TRANS-25
Brand: Trackmate Racing
SAVE 37% Transponders pack of 25 for R/C cars
Reference: trc-5
Brand: Trackmate Racing
SAVE 34% Transponders pack of 5 For R/C cars
Save dollars on your Slot car lap counter. This is a Do It Yourself version of the prewired LED kit. All the parts included to make an overhead light source for an infrared lap counter. Includes instructions, power adapter, LEDs, heat shrink, Connector and wire.
We include the highest quality infrared LEDs with the correct specifications for best performance. Alignment can be off by as much as 1/2 an inch and it will still work.
Trackmate Racing Infrared Kit Light Source For Slot Car Lap Counter
Download (45.29KB)Reference: ac232
USB to serial. Required if your computer does not have a 9 pin serial port and only has USB ports. New computers will most likely require the USB to serial.
Reference: CVGA-XX
Brand: Trackmate Racing
VGA extension cable - click view button and select length 15 pin Male / Female cable
Reference: RLY8
The perfect relay panel for 1:24 scale commercial tracks that run on batteries or 50 amp to 95 amp power supplies. Relay panel comes with 8 relays and master relay. Can be easily connected to Trackmate Commerical Interface.
Reference: PD6
Brand: Trackmate Racing
High quality power distribution box, no soldering or crimping required. Simply strip 3/16 inch from wire end and insert and screw down. One input and 6 power tap outputs. One required per lane. Board can be removed and then box can be securely screwed down for easy mounting.
Reference: flood8xx
Brand: Trackmate Racing
https://youtu.be/7NRAQ25uLaI?si=04Kl-lH8VNNlePq4&t=146Infrared Flood Bar, No alignment with sensors required. Select length required 12 Volt adapter included.
Reference: SC104
Brand: Trackmate Racing
Makes connecting to relay very easy, 2 terminal screws for each lane. Two terminal screws for relay coil.
Reference: Reed-4
Brand: Trackmate Racing
Four Reed switches for $14, Including heat shrink, Keep spares. Normally used with HO slot car lap counters.
Reference: ban3
3 banana plugs in white, black and red colors. Solder to controller wires
Reference: SC106
Brand: Trackmate Racing
For 6 lanes. Makes connecting to relay very easy, 2 terminal screws for each lane. Two terminal screws for relay coil.
Reference: SCLW
Wireless track call button, will require to solder 2 wires to the Tackmate interface, instructions included. Works up to 60 feet!
2 conductor 18 gauge wire 25' red and black, Ideal for wiring HO or 1:32 scale tracks.
Reference: 12v500ma
12 volt adapter. 500ma. For Slot car interface. Replaces older 9 volt adapters that were used in the past.Also used on LED Bridge/Gantries.
Reference: RLY4
Relay panel with 4 relays, one per lane giving the ability to control each lane individualy. Call for details
Reference: 12v1600n
12 volt adapter rated to 1.6 amps. Used on Sell time units with 4 to 8 relays. Required if you want to power more than 3 relays on a Trackmate interface.
Reference: GANTRY
Brand: Trackmate Racing
Gantry (Bridge) Uses infrared LEDs for light source. Recommended when using infrared sensors for lap counter . Includes DC adapter. Wires can go through table and be completely hidden. (Track not included). Click view and select type
Reference: 113
3 Alligator clips in White, Black and Red colors. Solder to controller wires
Save dollars on your Slot car lap counter. This is a Do It Yourself version of the prewired LED kit. All the parts included to make an overhead light source for an infrared lap counter. Includes instructions, power adapter, LEDs, heat shrink, Connector and wire.
